Production of Ceramic Green Bodies Using a Microwave-Reactive Organic Binder

Because the pyrolysis of organic substances can result in the emission of harmful pollutant gases, a reduction in the use of organic binders is one aim of today's ceramics industry. A novel ceramic-forming process was developed that requires considerably less organic binder than conventional techniques. The process involves immobilizing reactive molecules on the surfaces of the particles, which on subsequent irradiation with microwaves, form bridges that bind the entire particle assembly together. The chemical forces involved produce strong bonds, resulting in a significant reduction in the amount of organic binder that is required to maintain the shape of the ceramic green body. This method will help to decrease emissions of harmful gases produced from pyrolysis of the binder.     

Dynamic compensation by fusing a high-speed actuator and high-speed visual feedback with its application to fast peg-and-hole alignment

This paper presents a dynamic compensation concept to grapple with the dynamic defects of a traditional robot arm, especially while performing high-speed endpoint regulations. The proposed high-speed dynamic compensation concept offers a new point of view for cooperating with a traditional manipulator to realize highly dexterous performance of manipulations. The concept is realized through adoption of a high-speed light-weight actuator as well as endpoint closed loop configured high-speed cameras. The dynamic compensation is analyzed experimentally with 1000 Hz visual feedback and a high-speed finger for a robot arm in the case of one degree of freedom. The advantage of the proposed approach is that the modeling for the robot system’s dynamics is not needed, whereas it is necessary and trivial in order to realize high-speed regulations by traditional approaches. Thus, the control issue becomes easier with the proposed approach. As an application for this concept, fast peg-and-hole alignment with large position and attitude uncertainty is studied. The alignment algorithm is based on a visual compliance strategy. Alignment experiments show that with the proposed concept of dynamic compensation as well as visual compliant motion control, robust and fast convergence was realized for most cases.     

The reaction of polypropylene with maleic anhydride

An addition reaction of maleic anhydride with polypropylene takes place in the presence of radical reagents or sunlight. The initial rate of the reaction was proportional to the concentration of polypropylene and maleic anhydride, and one-half power of the concentration of the radical reagents. The increase in the temperature from 80 to 120°C increased the rate of the reaction and di-cumyl peroxide was effective as a radical reagent for this reaction. Ionic crosslinked rubber-like polymers were obtained from the reaction of maleic polypropylene with some alkali metal compounds. They showed the characteristic absorption band due to ? COO^? in their infrared spectra.     

高速气流冲击式粉体表面改性装置——HYBRIDIZATION系统及应用

利用高速气流冲击法进行粉体/粉体系表面改性技术,是迄今为止各种粉体材料开发中最为引人注目的技术之一。HYBRIDIZATION(下称HYB)系统是利用高速气流冲击法对微粉体进行干式/机械化处理,是使材料复合化的最实用的装置,可对各类有机物、无机物、金属等进行广泛组合,通用性很强,适用于许多行业领域。从本文所述的系统构成、型式,有关的典型球形化处理的运转特性,利用复合化高温粉体测定被处理粉体表面温度,利用颜料改变色调等的处理特点及该系统的适用性等(一部分是从已发表的学术论文及专利上摘录的),可以说明HYB系统的概况。     

Critical temperature for production of MAG by esterification of different FA with glycerol using <Emphasis Type="Italic">Penicillium camembertii</Emphasis> lipase

Production of MAG by a lipase-catalyzed reaction is known to be effective at low temperature. This phenomenon can be explained by assuming that synthesized MAG are excluded from the reaction system because MAG, which have low m.p., are solidified at low temperatures. Consequently, MAG are efficiently accumulated and do not serve as the precursor of DAG. If this hypothesis is correct, the critical temperature for MAG production, defined as the highest temperature at which DAG synthesis is repressed, should depend on the m.p. of the MAG. Esterification of FFA with glycerol using Candida rugosa, Rhizopus oryzae, and Penicillium camembertii lipases produced MAG efficiently at low temperatures. However, Candida lipase showed very low esterification activity at high temperatures (>20°C), and Rhizopus lipase produced not only MAG but also DAG even at low temperatures. Meanwhile, P. camembertii lipase catalyzed synthesis of MAG only from FFA and glycerol at low temperatures, although the enzyme catalyzed synthesis of DAG from MAG in addition to synthesis of MAG at high temperatures. We thus studied the effect of temperature on esterification of C₁₀−C₁₈ FFA with glycerol using Penicillium lipase as a catalyst and determined the critical temperatures for production of MAG. The critical temperature for production of each MAG showed a linear correlation with m.p. of the MAG, which supported the hypothesis. In addition, because the m.p. of MAG are estimated from that of the constituent FA, the optimal temperature for production of MAG can be predicted from the m.p. of the FFA used as a substrate.     

Fractionation and enrichment of CLA isomers by selective esterification with Candida rugosa lipase

A commercial product of CLA contains almost equal amounts of cis-9,trans-11 (c9,t11)-CLA and trans-10,cis-12 (t10,c12)-CLA. We attempted to enrich the two isomers by a two-step selective esterification using Candida rugosa lipase that acted on c9,t11-CLA more strongly than on t10,c12-CLA. An FFA mixture containing CLA isomers was esterified with an equimolar amount of lauryl alcohol in a mixture of 20% water and the lipase. When the esterification of total FA reached 50%, two isomers were fractionated in a good yield: t10,c12-CLA was enriched in FFA, and c9,t11-CLA was recovered in lauryl esters. The FFA were esterified again to enrich t10,c12-CLA. At 27.3% esterification of total FA, the t10,c12-CLA content in FFA increased to 64.8 wt% with 89.3% recovery: The ratio of the content of t10,c12-CLA to that of two isomers was 95.9%. Lauryl esters obtained by the single esterification were employed for enrichment of c9,t11-CLA. After the esters were hydrolyzed, the resulting FFA were esterified again with lauryl alcohol. At 62.0% esterification of total FA, the c9,t11-CLA content in lauryl esters increased to 73.3 wt% with 79.4% recovery: The ratio of the content of c9,t11-CLA to that of two isomers was 95.6%. In a 600-g-scale purification, molecular distillation was effective in separating the reaction mixture into lauryl alcohol, FFA, and lauryl ester fractions.     

影响啤酒酵母菌吸附铅离子条件的研究

采用啤酒酵母自制生物吸附剂用于吸附金属铅离子,考察了pH值、反应时间、酵母浓度及金属离子浓度对啤酒酵母吸附Pb2 的影响.单因素实验结果表明,当pH值为5.0、溶液初始Pb2 浓度为80 mg·L-1、啤酒酵母的浓度为1.0 g·L-1、反应时间为0.5 h时,吸附效果最佳.通过正交实验,确定初始Pb2 浓度为反应过程中的显著因素.     

Preparation of therapeutic phospholipids through porcine pancreatic phospholipase A2-mediated esterification and lipozyme-mediated acidolysis

Highly unsaturated fatty acid-containing phospholipids (HUFA-PL), which serve to increase the deformability of human red blood cells, were prepared through porcine phospholipase A₂-mediated esterification of the lysophosphatidylcholine, which was derived from soy phosphatidylcholine (PC), and by Lipozyme-mediated acidolysis. Through these processes, phospholipase A₂, with formamide as a water mimic, enhanced the incorporation of HUFA into positionsn-2 of PC and suppressed hydrolysis of the synthesized PL. On the other hand, Lipozyme-mediated acidolysis between positionsn-1 of soy PC and HUFA was enhanced by a combination of water and propylene glycol. Simultaneously, the recovered PL products showed decreased hydrolysis of newly synthesized health-beneficial HUFA-PL.     

Production of FAME from acid oil model using immobilized <Emphasis Type="Italic">Candida antarctica</Emphasis> lipase

Acid oil is a by-product in the neutralization step of vegetable oil refining and is an alternative source of biodiesel fuel. A model substrate of acid oil, which is composed of TAG and FFA, was used in experiments on the conversion to FAME by immobilized Candida antarctica lipase. FFA in the mixture of TAG/FFA were efficiently esterified with methanol (MeOH), but the water generated by the esterification significantly inhibited methanolysis of TAG. We thus attempted to convert a mixture of TAG/FFA to FAME by a two-step process comprising methyl esterification of FFA and methanolysis of TAG by immobilized C. antarctica lipase. The first reaction was conducted at 30°C in a mixture of TAG/FFA (1∶1, wt/wt) and 10 wt% MeOH using 0.5 wt% immobilized lipase, resulting in efficient esterification of FFA. The reaction mixture after 24 h was composed of 49.1 wt% TAG, 1.3 wt% FFA, 49.1 wt% FAME, and negligible amounts of DAG and MAG (<0.5 wt%). The reaction mixture was then dehydrated and used as a substrate for the second reaction, which was conducted at 30°C in a solution of the dehydrated mixture and 5.5 wt% MeOH using 6 wt% immobilized lipase. The activity of the lipase increased gradually when the reaction was repeated by transferring the enzyme to a fresh substrate mixture. The activity reached a maximum after 6 cycles, and the content of FAME achieved was >98.5 wt% after a 24-h reaction. The immobilized lipase was very stable in the first-and second-step reactions and could be used for >100 d without significant loss of activity.     

Improvement of corrosion resistance of magnesium metal by rare earth elements

Mg metal containing rare earth metals (REs) can be electrowon directly by molten salt electrolysis. The clarification of the optimum RE content in Mg is necessary to fix the electrolytic conditions in the direct electrowinning of Mg with RE. From this point of view, effect of RE addition in Mg metal on its corrosion property was studied in detail in this study. The specimen was prepared by adding La, Nd, or Ce in melted Mg metal, and its corrosion resistance was examined by an immersion test in 3 mass%-NaCl solution at room temperature. The corrosion resistance of Mg was improved greatly by adding a small amount of RE, whereas the excess addition of RE deteriorated the corrosion resistance. The optimum RE content was about 0.5 mass%. In this study, the corrosion property of Mg with an artificial surface oxide layer was also studied to clarify the effect of surface oxide. The corrosion resistance of Mg was particularly strengthened by conversion coating in a solution including La(NO₃)₃, Nd(NO₃)₃, or Ce(NO₃)₃, with Mg(NO₃)₂. This result suggests that the surface oxide film consisting of both Mg and RE gives ideal corrosion resistance to Mg metal. Mg metal with conversion coating including RE should also be of use as a corrosion-resistant material.